cra04s www.vishay.com vishay revison: 23-feb-17 1 document number: 31043 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 thick film chip resistor array the cra04s thick film resistor array is constructed on a high grade ceramic body with convex terminations. a small package enables the design of high density circuits. the single component reduces board space, component counts, and assembly costs. features ? convex terminal array with square corners ? wide ohmic range: 10r to 1m0 ? 4 or 8 terminal package with isolated resistors ? aec-q200 qualified ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 notes (1) rated voltage: (2) the power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow suppor t of the printed-circuit boar d (thermal resistance). the rate di ssipation applies only if the permitted film temp erature of 155 c is no t exceeded notes (1) preferred way for ordering produc ts is by use of the part number (2) please refer to the table packaging, see next page standard electrical specifications model circuit power rating p 70 c w limiting element voltage max. v ? temperature coefficient ppm/k tolerance % resistance range ? e-series cra04s 03 0.063 50 100 1 10 to 1m 24 + 96 200 2; 5 24 zero-ohm-resistor: r max. ? 50 m ? , i max. = 1 a technical specifications parameter unit cra04s rated dissipation at 70 c (2) w per element 0.063 limiting element voltage (1) v ? 50 insulation voltage (1 min) v dc/ac peak 100 category temperatur e range c -55 to +155 insulation resistance ? > 10 9 part number and product description part number: cra04s08347k0jtd (1) model terminal style pin circuit value tolerance packaging (2) special cra04 s 04 08 3 = 03 r = decimal k = thousand m = million 0000 = 0 ? jumper f = 1 % g = 2 % j = 5 % z = 0 ? jumper td tc pz up to 2 digits product description: cra04s 08 03 473 j rt7 e3 cra04s 08 03 473 j rt7 e3 model terminal count circuit type resistance value tolerance packaging (4) lead (pb)-free cra04s 04 08 03 473 = 47 k ? 4702 = 47 k ? 10r0 = 10 ? 100 = 10 ? 000 = 0 ? jumper f = 1 % g = 2 % j = 5 % z = 0 ? jumper rt7 rt6 pz e3 = pure tin termination finish first two digits (3 for 1 %) are significant. last digit is the multiplier. p x r a04s 834 0 cr jd k 0t 7
cra04s www.vishay.com vishay revison: 23-feb-17 2 document number: 31043 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 circuit derating dimensions the dimensions shown are for a 8 pin part. for parts with different pin numbers use th e same pitch and add or subtract pads as required. packaging model tape width diameter pitch pieces/reel packaging code paper tape part number product description cra04s 8 mm 180 mm/7" 2 mm 10 000 td rt7 330 mm/13" 2 mm 20 000 tc rt6 330 mm/13" 2 mm 50 000 pz pz 03 circuit 4 pin 8 pin - 55 - 25 0 25 50 75 100 125 155 175 120 100 8 0 60 40 20 0 70 ambient temperature in c rated power in % ae e pin ? no # dimensions in millimeters laa 1 bb*p nom. tw 4 1.0 0.1 - 0.33 0.15 0.25 0.65 0.35 1.0 8 2.0 0.2 0.30 0.4 0.15 0.25 0.50 0.45 1.0 tol. - 0.15 0.15 0.10 0.1 - 0.1 0.15 solder pad dimensions in millimeters cwdabe wave 0.45 1.45 0.2 0.4 0.5 0.3
cra04s www.vishay.com vishay revison: 23-feb-17 3 document number: 31043 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) figures are given for a single element (2) solderability is specified for 2 years after production or requalification. permitted storage time is 20 years test procedures and requirements en 60115-1 test ? (clause) conditions of test requirements permissible change ( ? r / r ) (1) stability class 1 or better stability class 2 or better stability for product types: 10 ? to 1 m ? 10 ? to 1 m ? cra04s resistance (4.5) - 1 % 2 %; 5 % temperature coefficient (4.8.4.2) (20 / -55 / 20) c and (20 / 125 / 20) c 100 ppm/k 200 ppm/k overload (4.13) u = 2.5 x ( p 70 x r ) 1/2 ? 2 x u max. ; 0.5 s (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) solderability (4.17.5) (2) aging 4 h at 155 c, dry heat solder bath method; 235 c; 2 s visual examination good tinning ( ? 95 % covered) no visible damage resistance to soldering heat (4.18.2) solder bath method; (260 5) c; (10 1) s (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) rapid change of temperature (4.19) 30 min at lct = -55 c; 30 min at uct = 125 c; 5 cycles (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) damp heat, steady state (4.24) (40 2) c; 56 days; (93 3) % rh (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) climatic sequence (4.23) 16 h at uct = 125 c; 1 cycle at 55 c; 2 h at lct = -55 c; 1 h/1 kpa at 15 c to 35 c; 5 cycles at 55 c u = ( p 70 x r ) 1/2 u = u max. ; whichever is less severe (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) endurance at 70 c (4.25.1) u = ( p 70 x r ) 1/2 u = u max. ; whichever is less severe 1.5 h on; 0.5 h off; 70 c; 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) extended endurance (4.25.1.8) duration extended to 8000 h (2 % r + 0.1 ? ) (4 % r + 0.1 ? ) endurance at upper category temperature (4.25.3) uct = 125 c; 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) applicable specifications ? en 60115-1 ? ? en 140400 ? ? en 140401-802 ? ? iec 60068-2-x ? ? eia 481 generic specification ? sectional specification ? detail specification ? variety of environmental test procedures ? packaging of smd components
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
